![]() Always make sure to properly secure the new connector tube to prevent any leaks or loss of vacuum pressure while driving. The job can take approximately 15-30 minutes to complete, depending on the installer's skill level and familiarity with the vehicle. It is important to note that this installation requires beginner-level skills and should be easy to complete for most individuals. Set the parking brake and disconnect the connector to the evaporative emission (EVAP) canister. Test the new connector tube to ensure proper fit and alignment.Install the new Genuine Ford PCV hose valve connector tube by aligning it with the PCV valve and the air intake hose, and securing it with clamps.Carefully remove the old connector tube from the vehicle.Use pliers to carefully remove the old connector tube from the PCV valve and the air intake hose. ![]() The connector tube is typically located on the engine, near the valve cover. Locate the PCV hose valve connector tube on your 2002-2015 Ford Ranger 3.0.Note: Before starting the installation, ensure that the vehicle is parked on a level surface. Installation Time: Approximately 15-30 minutes Proper crankcase ventilation is key to smooth performance and engine longevity. It is a direct replacement for the original equipment manufacturer (OEM) part, ensuring a perfect fit and optimal performance. 1 Year Limited Warranty Centerline Length (in): 18-1/8 Inch Centerline Length (mm): 460mm End 1 Type: Clip-On Compare Gates Plastic, Rubber Emission Hose - EMH071 Part : EMH071 Line: GAT 0. This high-quality, new genuine Ford part is specifically designed to fit the 2002-2015 Ford Ranger 3.0 models. then remove the PCV hose between cambox and intake manifold and any other. SKU: 97237110 Other Names: Connector Description: This GM Genuine Part is designed. Start the engine and then disconnect the wiring connector from what you think. It includes affordable wholesale pcv valve hose connector that can. Positive Crankcase Ventilation (PCV) Hose Connector 97237110. I haven't been able to figure out what this thing is called to make any headway in searching for a replacement.Are you experiencing issues with your PCV system on your 2002-2015 Ford Ranger 3.0? The Genuine OEM PCV Hose Valve Connector Tube may be the solution you need. The Garden Water Connectors section has the essential equipment for gardening jobs. (1) Check Vehicle Fit 1 Year Limited Warranty Centerline Length (in): 7 Inch Material: Nitrile Rubber (NBR) Attachment Method: Push-On Compare Representative Image Gates Safety Stripe Fuel Hose - 27027 Part : 27027 Line: GAT 0. 000-987-27-27 - Black Tecalan (plastic) evap tube, 8mm - From PCV tubes to regen valve near EZL (1.6 meters required) See attached PDF file for the complete list of part numbers from the EPC. Since this car is my only way around, I was too afraid of the thing crumbling to pieces if I handled it too much, so I didn't want to pull it apart to get a better look at it. 119-078-00-81 - Rubber hose connector for 8mm evap tube, at intake manifold. The white spot on this connector is hard and crystalline, like dry superglue: Not only are there zip ties holding the hose together, but it appears that someone's also tried to use superglue to hold it together. While inspecting closer I found this piece connected to the PCV hose near my throttle body that inserts into the air intake manifold. In preparation of changing both the hoses and the PCV valve, I was looking everything over and tracing the hoses around to see what exactly I needed to buy for replacement. Is this the complete list or is there anything missing to replace ALL PCV hoses 116 A 102 094 02 12 CONNECTOR FROM CONNECTOR TO CYLINDER HEAD COVER (x2). I know that the PCV hoses in my car need some TLC that fact is readily apparent because someone has liberally applied zip ties to some of them to keep them in place.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |